So how to build outdoor copper shower head. So im going to explain you guys how you guys can make a outdoor shower easily. Please follow the steps that explained bellow correctly. This guide is for anyone with an outdoor faucet. If you need hot water for an outdoor shower, hire a plumber to supply you with hot and cold water.
How to build outdoor copper shower head – First step you need to do
Choose a location for an outdoor shower. Choose a relatively flat location, a slight slope will promote runoff. Consider how close it is to your outdoor faucet and the relative privacy it provides.
Secondly do this
Build a base. Cut a 4 x 4 square into four equal 23 pieces. Then assemble the base square with screws. Next, cut the 1 x 4 into 7 26-1/2 pieces and lay them evenly over the base, leaving about 1/4 of space between the boards for drainage. Secure the rails to the frame with 3-1/3 screws. Apply wood sealer to the entire base and 2.5m 4″ x 4″ uncut sections and let dry.
Then after follow these steps
Install the shower. Use an auger to dig a 12 deep hole and insert the 8′ 4 x 4. You can use concrete to hold it in place, or simply fill the hole with dirt. Place a shower tray at side of the 4 x 4, mark its location, then remove the shower tray and cover the floor with gravel or small stones to allow drainage. Lay a foundation on the gravel.
Then install the pipes
Install the pipes. Please use a drill to drill it like 4×4 hole and it need to be 6ft up from ground. Above the floor and 2-1/2 above the base. Connect the pipes in the following order : Shower head – Shower head – 90° Elbow – Length 48 – Faucet – Length 24 – Elbow 90° – Length 6 Use nylon tubing at each joint. Next, insert a 6 long horizontal pipe through the hole in the bottom of the 4 x 4 vertical support and mount it flush with the front. Secure the pipe to the 4 with 2-1/4 screws. And also you need use 2×4 pipe clamps as well.
Add water afterward
Add water. Connect the hose to the connector on the back of the shower. You may want to purchase an outside faucet y-piece to use the extra hose for lawn and garden work. Taste the water.
How to build outdoor copper shower head – Build an outdoor shower
Whether you’re spending a day at the beach, exploring the woods, or gardening, outdoor living can quickly get messy. Rather than stepping into the house at the end of the day, this outdoor shower is a surprisingly affordable luxury. Offering enough privacy for bathing or changing clothes, and convenient enough for washing feet, kids, or pets, this weekend project can be built anywhere you have a garden hose using lumber simple, corrugated iron and simple plumbing assemblies.
set location
Find a flat, well-drained area on which to build your outdoor shower. Choose a location for the back right corner of the fence, then use the shovel to dig a hole 24 inches deep and 6 inches in diameter.
Measure and dig post holes
Dig three more post holes 24 inches deep, 46 1/2 inches apart, to form a square. The 2 x 4 x 46 1/2 board that will be used in the next steps can be placed on the ground as a spacer instead of a tape measure. Place a 4 x 4 x 9′ post in the hole .
How to build outdoor copper shower head – Level messages
Make sure the post is fully seated in the hole and level it with a spirit level. All posts should be the same height, 7 feet. Nail or screw temporary dowels to adjacent sides of each post to hold them in place. Although all the posts are theoretically aligned and perfectly positioned, using stakes rather than filling in the holes at this stage will make any adjustments needed when setting up the frame easier.
Attach the top rail
With a helper, close the space between the straight studs with a 2 x 4 x 46 1/2 board and support it with fasteners. Center and align the wood flush with the top of each stud. Make sure the rails are level (in section After making any necessary adjustments) and secure with two 3 screws on each post. Remove the clips once securely attached.
Attach the remaining top rails
Repeat the process shown in the previous step to attach the secure top rails to the rear and left side of the enclosure leaving the front open.
Attach the bottom rail
Mark a point 12 inches from the ground on each post. Working one board at a time, attach 2 4 x 46-1/2 inch slats between the studs using the same method as the top slats. If the ground is not completely level, you will need to adjust the bottom rails before attaching them to each post with two 3 screws.
How to build outdoor copper shower head – Attach the vertical supports
Install 2 x 65 rails on each post between the top and bottom rails. The fit may be tight – use a rubber mallet or wood block to push the vertical supports into place. Secure the posts to the posts with 3 screws and attach them to the top and bottom rails by placing the screws at an angle. Now the pre-made frame is used to hang the wall and also helps stabilize the structure.
So this is all i can say about how to build outdoor copper shower head. I hope that this article helped you with what you looking for i will see you guys soon.